Oil Furnace Tune Up Checklist
Checked thermostat and made adjustments where necessary
Tested safety controls
Removed rust and soot and cleaned and adjusted burners
Replaced oil filter
Replaced nozzle and adjusted electrodes
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap in high efficiency units
Adjusted barometric damper
Checked transformer
Inspected and adjusted belts
Checked filter and replaced with consent if necessary
Checked and tightened all exhaust pipe connections
Clean and adjusted fan timer
Inspected and cleaned heat exchanger thoroughly
Ensured correct temperature rise
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Inspected blower access door and ensured correct operation
Checked CO level of exhaust
Checked fire pot, comb. air wheel and pump coupling
Checked all oil connnections in unit
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and
any necessary recommendations.
Checked thermostat and made adjustments where necessary
Tested safety controls
Removed rust and soot and cleaned and adjusted burners
Replaced oil filter
Replaced nozzle and adjusted electrodes
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap in high efficiency units
Adjusted barometric damper
Checked transformer
Inspected and adjusted belts
Checked filter and replaced with consent if necessary
Checked and tightened all exhaust pipe connections
Clean and adjusted fan timer
Inspected and cleaned heat exchanger thoroughly
Ensured correct temperature rise
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Inspected blower access door and ensured correct operation
Checked CO level of exhaust
Checked fire pot, comb. air wheel and pump coupling
Checked all oil connnections in unit
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and
any necessary recommendations.
Gas Boiler Tune Up Checklist
Checked thermostat and made adjustments where necessary
Drained expansion tank if unit has isolation valves
Tested flue damper operation
Checked/adjusted temp and pressure settings
Tested safety controls
Removed rust and soot and cleaned and adjusted burners and
exchanger
Cleaned and adjusted ignition assembly or OHM igniter
Checked micro amp signal from flame sensor
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap if high efficiency boiler
Checked CO level of exhaust
Checked and tightened all exhaust pipe connections
Checked all gas connections located in unit
Adjusted gas/pilot pressure
Inspected and cleaned heat exchanger thoroughly
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and
any necessary recommendations.
Checked thermostat and made adjustments where necessary
Drained expansion tank if unit has isolation valves
Tested flue damper operation
Checked/adjusted temp and pressure settings
Tested safety controls
Removed rust and soot and cleaned and adjusted burners and
exchanger
Cleaned and adjusted ignition assembly or OHM igniter
Checked micro amp signal from flame sensor
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap if high efficiency boiler
Checked CO level of exhaust
Checked and tightened all exhaust pipe connections
Checked all gas connections located in unit
Adjusted gas/pilot pressure
Inspected and cleaned heat exchanger thoroughly
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and
any necessary recommendations.
Oil Boiler Tune Up Checklist
Checked thermostat and made adjustments where necessary
Drained expansion tank if unit has isolation valves
Tested flue damper operation
Checked/adjusted temp and pressure settings
Tested safety controls
Removed rust and soot and cleaned and adjusted burners and
exchanger
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap if high efficiency boiler
Checked CO level of exhaust
Checked and tightened all exhaust pipe connections
Inspected and cleaned heat exchanger thoroughly
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Replaced oil filter
Replaced nozzle and adjusted electrodes
Adjusted barometric damper
Checked transformer
Checked fire pot, comb. air wheel, and pump coupling
Checked all oil connections in unit
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and any necessary recommendations.
Checked thermostat and made adjustments where necessary
Drained expansion tank if unit has isolation valves
Tested flue damper operation
Checked/adjusted temp and pressure settings
Tested safety controls
Removed rust and soot and cleaned and adjusted burners and
exchanger
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap if high efficiency boiler
Checked CO level of exhaust
Checked and tightened all exhaust pipe connections
Inspected and cleaned heat exchanger thoroughly
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Replaced oil filter
Replaced nozzle and adjusted electrodes
Adjusted barometric damper
Checked transformer
Checked fire pot, comb. air wheel, and pump coupling
Checked all oil connections in unit
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and any necessary recommendations.
Air Conditioner Tune Up Checklist
Checked thermostat and made adjustments where necessary
Tightened all electrical connections
Inspected low and high volt wiring
Oiled condenser fan motor
Tested safety controls
Cleaned evaporator drain
Cleaned rubbish out of condenser and cleaned with coil cleaner
Checked refrigerant level and advised leak detection if necessary
Cleaned and adjusted blower components
Checked indoor evaporator temp drop
Inspected and adjusted belts
Adjusted humidifier dampers
Measured evaporator super heat
Tightened all refrigerant valve caps
Checked and replaced filter with consent if necessary
Resealed outside line set penetration if necessary
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and any necessary recommendations
Checked thermostat and made adjustments where necessary
Tightened all electrical connections
Inspected low and high volt wiring
Oiled condenser fan motor
Tested safety controls
Cleaned evaporator drain
Cleaned rubbish out of condenser and cleaned with coil cleaner
Checked refrigerant level and advised leak detection if necessary
Cleaned and adjusted blower components
Checked indoor evaporator temp drop
Inspected and adjusted belts
Adjusted humidifier dampers
Measured evaporator super heat
Tightened all refrigerant valve caps
Checked and replaced filter with consent if necessary
Resealed outside line set penetration if necessary
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and any necessary recommendations
Gas Furnace Tune Up Checklist
Checked thermostat and made adjustments where necessary
Tested safety controls
Removed rust and soot and cleaned and adjusted burners
Cleaned and adjusted ignition assembly or OHM igniter
Checked micro and signal from flame sensor
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap
Checked all gas connections located in unit
Adjusted gas/pilot pressure
Inspected and adjusted belts
Checked filter and replaced with consent if necessary
Checked and tightened all exhaust pipe connections
Clean and adjusted fan timer
Inspected and cleaned heat exchanger thoroughly
Ensured correct temperature rise
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Inspected blower access door and ensured correct operation
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and any necessary recommendations.
Checked thermostat and made adjustments where necessary
Tested safety controls
Removed rust and soot and cleaned and adjusted burners
Cleaned and adjusted ignition assembly or OHM igniter
Checked micro and signal from flame sensor
Adjusted gas/air mixture for optimum efficiency
Oiled motor bearings
Cleaned condensate trap
Checked all gas connections located in unit
Adjusted gas/pilot pressure
Inspected and adjusted belts
Checked filter and replaced with consent if necessary
Checked and tightened all exhaust pipe connections
Clean and adjusted fan timer
Inspected and cleaned heat exchanger thoroughly
Ensured correct temperature rise
Checked electrical wiring and tightened all electrical connections
Cycled unit and made adjustments accordingly
Inspected blower access door and ensured correct operation
Analyzed unit’s operation and appearance and informed of its efficiency,
condition and any necessary recommendations.
